Diasen Argacem HP
Diasen Argacem HP
Semi-smooth lime based finishing plaster
To achieve an authentic beautiful finish while maintaining the breathability of the wall/ceiling.
Use it on
All Diasen Diathonite plasters, Watstop and any new or old lime or cement-based plasters.
Argacem HP is a smoothing plaster skim coat typically used with the range of Diasen Diathonite plasters. It is highly breathable, mould resistant and made from natural materials including hydrated lime, natural filler and pure limestone powder. It is very workable and can be applied by spraying with a suitable machine or by trowel. It can be used internally and externally and should be always painted over, ideally with a breathable paint.
Where to use it
Argacem HP is an internal or external smoothing skim coat designed for use with Diasen’s Diathonite plasters. It can be applied directly over any Diathonite plaster with no other preparation.
It is suitable for new builds and retrofits, including Heritage and Listed buildings.
It is also compatible with other new and old lime or cement-based plasters that have been suitably prepared. Argacem HP can be used directly on to Diasen Watstop Waterproofing System.
What it does
Argacem HP provides a semi-smooth finish for covering the granular texture of Diathonite Evolution and Thermactive without affecting the breathability of the wall.
It is easy to mix to a consistent texture and offers excellent workability. It can be hand applied or sprayed on with a plaster spraying machine for quicker application in large areas.
Similar to other breathable finishing plasters, Argacem HP must always be painted with a breathable paint finish. The plaster is quite absorbent so this final finishing ensures the surface will remain clean and stain free.
How it works
Argacem HP is easy to mix with just clear water to create a consistent mixture with excellent workability. It is lime-based and in combination with Diathonite plasters, provides excellent thermal comfort and humidity balance.
Why we love it
Argacem HP’s powdery consistency makes it easy to combine with water to create a consistent mixture with excellent workability. It can also be finished with a plastic float or a sponge. An experienced lime plasterer or DIY enthusiast can install it without special training.
The slightly grainy texture provides a semi-smooth finish to create a traditional look or contemporary aesthetic.
By containing only natural materials, Argacem HP qualifies for LEED points, which means it can be used in projects with strict environmental requirements.
It is also non combustible and does not emit smoke. It can therefore contribute to improved fire safety of the building.
You can see the beautiful finish achieved in this Barn Conversion in Northumberland
- All-natural materials
- Easy to mix
- Grain size 0-0.6mm
- No special training required
- Fireproof and non-combustible
- Low thermal conductivity
- Breathable (vapour open)
- Durable finish
- Completes a breathable wall on top of Diathonite plasters, regulating humidity & preventing mould growth.
- Smooths plaster surfaces to achieve a traditional or contemporary finish.
- Any experienced lime plasterer can install.
- Does not burn or smoke improving fire safety.
- In combination with Diathonite plasters it provides excellent thermal comfort.
- The powder is easy to mix with excellent workability and consistency, and can be hand applied or sprayed with a plaster machine.
There are currently no questions and answers published for this product
You may also need
Key Technical Data
How to Install
When applied over fully dried Diathonite plasters, Argacem HP requires no special surface preparation. Over old plasters, an adhesion test is recommended to determine if Aquabond primer is required first.
Argacem HP should be applied in two layers with a steel plastering spatula. Each layer should be approximately 1.0-1.5mm per layer. The first layer smooths the texture of the Diathonite and regulates the porosity of the surface. The second layer must be applied when the previous one is firm to the touch; typically after 12/24 hours at 20C, 40% relative humidity.
Diasen Polites-80 reinforcing mesh is recommended for use at stress points around windows, corners and power sockets. Apply the mesh with an overlap of 100mm between the first and second coat of plaster.
Hints & Tips
Under extremely hot weather conditions you may need to mist the first layer with water before applying the second coat. Please contact our technical team for advice in these circumstances.
While the second layer is still moist, finish with a plastic trowel or sponge to achieve the aesthetic finish you require.